Nylon 6/6 Shoulder Washer, 0.382" ID, 0.500" OD, 0.062" Thick, 1.000" Shoulder Diameter, 0.562" Length (Pack of 50)

Nylon 6/6 Shoulder Washer, 0.382" ID, 0.500" OD, 0.062" Thick, 1.000" Shoulder Diameter, 0.562" Length (Pack of 50) Reviews

Other Picture

Nylon 6/6 Shoulder Washer, 0.382" ID, 0.500" OD, 0.062" Thick, 1.000" Shoulder Diameter, 0.562" Length (Pack of 50) Feature

• Shoulder Washers protect screws, wire, and tubing from corrosion
• Nylon 6/6 is suitable where non-conductivity, corrosion resistance, and cost are important considerations
• Size Name corresponds to matching screw or bolt size

Shoulder Washers, also known as insulator washers and shoulder spacers, insulate and protect screws, wire, and tubing from corrosion.

Nylon 6/6 is a general purpose thermoplastic with outstanding resistance to organic chemicals, acids and alkalis. Nylon wears well against other surfaces; it is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications which should be taken into account with its use. Tensile strength of this material is 12,000 psi (pounds per square inch).

Visit Store Now !!

Detail Products

• Nylon 6/6 Flat Washer, DIN, M3, 3.20mm ID, 8mm OD, 0.8mm Thick (Pack of 100)
• Nylon 6/6 Hex Nut, #4-40 (Pack of 100)
• Nylon 6/6 Hex Bolt, #4-40, 1/4" Length (Pack of 100)
• Nylon 6/6 Machine Screw, Binding Head, Slotted Drive, #4-40, 1" Length (Pack of 100)
• Nylon 6/6 Machine Screw, Cheese Head, Slotted Drive, M5-0.8, 6mm Length (Pack of 100)

Detail Reviews

Plain Flat Washer, IFI Type B, Low Carbon Steel, Zinc Plated, Round Shape, USA Made, 0.125" ID, 0.375" OD, 0.036-0.045" Thick (Pack of 100)

Plain Flat Washer, IFI Type B, Low Carbon Steel, Zinc Plated, Round Shape, USA Made, 0.125" ID, 0.375" OD, 0.036-0.045" Thick (Pack of 100) Reviews

Other Picture

Plain Flat Washer, IFI Type B, Low Carbon Steel, Zinc Plated, Round Shape, USA Made, 0.125" ID, 0.375" OD, 0.036-0.045" Thick (Pack of 100) Feature

• Type B Flat Washers are manufactured to the IFI Standards (Industrial Fastener Institute) and are used in general industrial applications
• Type B washers are specified in many industrial and appliance applications
• Stamped from low carbon steel, and commercial zinc plated - RoHs compliant
• Industrial, Appliance, MRO, general applications
• Made In USA for excellent quality conformance

Type B Flat Washers are manufactured to the Industrial Fastener Institute Type B specification. Originating in 1965 ASME B18.22.1 established a categoruy of Tyoe A and Type B Flat Washer dimensions. The Type B are available in narrow, regular, and wide series, with proportions designed for distributing load over larger areas of low strength materials. Available from stock in screw sizes from #0 through 1/2" bolt sizes. Manufactured of Low Carbon Steel, with a protective silver Zinc plating (RoHs compliant).

Made in the USA. These flat washers are produced in the USA for excellent quality conformance. One of the significant differences between less expensive imported products and ours are the way we stamp. Many cheap imports are produced on gang dies that produce 10 or more washers per stroke of the press. Using such a large die means that the individual washer sets are not adjustable - when the punch wears, the dimensions change and there is no way to fix this as the press produces washers, leading to a large variation in the finished part.

Materials available in many other countries are not as consistent as the domestic steels we use, which gives the imports a cheaper cost, but can lead to failures and inconsistencies when the products are used. The Defense Federal Acquisition Regulation Supplement (DFARS) was created to address this problem. Our materials are DFARS compliant although we do not supply the certification except on special order.

Visit Store Now !!

Detail Products

Detail Reviews

UST Washers - 720-Pc. Set, Model# UST5218

UST Washers - 720-Pc. Set, Model# UST5218 Reviews

Other Picture

Contains 12 most popular sizes. Resealable plastic case.

Visit Store Now !!

Detail Products

Detail Reviews

Fender Flat Washer, 316 Stainless Steel, Round Shape, Plain Finish, USA Made, 5/16" Bolt Size, 0.344" ID, 2.000" OD, 0.052-0.072" Thick (Pack of 10)

Fender Flat Washer, 316 Stainless Steel, Round Shape, Plain Finish, USA Made, 5/16" Bolt Size, 0.344" ID, 2.000" OD, 0.052-0.072" Thick (Pack of 10) Reviews

Other Picture

Fender Flat Washer, 316 Stainless Steel, Round Shape, Plain Finish, USA Made, 5/16" Bolt Size, 0.344" ID, 2.000" OD, 0.052-0.072" Thick (Pack of 10) Feature

• Fender Flat Washers have extra large outside diameters in relation to their bolt size
• Extra large Outside Diameter spreads the load over a wider area
• 316 Stainless Steel offers more corrosion resistance over the standard 18-8 grades
• Great for exposure to salt water, chemical rich environments

Fender Flatwashers were named because of their original use in auto body repair. The large outer diameter covered up a lot of area, and also spread the load across a wide area of thin sheet metal. In todays world these washers are used in electrical, construction, HVAC, and general industrial applications. The purpose of a washer is to spread the load from the head of the bolt across a wider area than the bolt head, which increases the strength of the joint. Fender washers do this well because the outer diameter is so much larger than the diameter of a standard flat washer. These standard (thin) Fender washers are manufactured in Steel Zinc, 18-8 Stainless Steel, and Type 316 Stainless Steel.

Made in the USA. These flat washers are produced in the USA for excellent quality conformance. One of the significant differences between less expensive imported products and ours are the way we stamp. Many cheap imports are produced on gang dies that produce 10 or more washers per stroke of the press. Using such a large die means that the individual washer sets are not adjustable - when the punch wears, the dimensions change and there is no way to fix this as the press produces washers, leading to a large variation in the finished part.

Materials available in many other countries are not as consistent as the domestic steels we use, which gives the imports a cheaper cost, but can lead to failures and inconsistencies when the products are used. The Defense Federal Acquisition Regulation Supplement (DFARS) was created to address this problem. Our materials are DFARS compliant although we do not supply the certification except on special order.

Visit Store Now !!

Detail Products

• Stainless Steel 316 Hex Bolt, 1/4"-20, 1-1/4" Length (Pack of 50)
• Stainless Steel 316 Machine Screw, Flat Head, Phillips Drive, #10-32, 3/4" Length (Pack of 25)
• Stainless Steel Lock Nut, #6-32 (Pack of 100)
• Stainless Steel 316 Machine Screw, Pan Head, Phillips Drive, #4-40, 1/4" Length (Pack of 25)
• Stainless Steel 18-8 Flat Washer, ANSI, #5, 0.141" ID, 0.5" OD, 0.04" Thick (Pack of 100)

Detail Reviews

Square Flat Washer, 18-8 Stainless Steel, Square Shape, USA Made, 1/4" Bolt Size, 0.313" ID, 2.000" OD, 0.250" Thick (Pack of 1)

Square Flat Washer, 18-8 Stainless Steel, Square Shape, USA Made, 1/4" Bolt Size, 0.313" ID, 2.000" OD, 0.250" Thick (Pack of 1) Reviews

Other Picture

Square Flat Washer, 18-8 Stainless Steel, Square Shape, USA Made, 1/4" Bolt Size, 0.313" ID, 2.000" OD, 0.250" Thick (Pack of 1) Feature

• Square Flat Washers are used as shims in construction applications, as well as in industrial and commercial products
• Inner diameter is oversized by 1/16" to allow for maximum flexibility
• 18-8 Stainless Steel is the most common corrosion resistant Stainless Steel used in Flat Washers
• Construction, Power Transmission, Power Generation, Mining, and MRO applications are all covered with these Square Washers
• Made In USA for excellent quality conformance

Square Washers are most often used in construction where building codes specify them as a structural component of framing and other subsystems, or in channels or square tubing. The square shape prvents them from rotating in the channel. Our square washers are manufactured with extra thick steel and stainless steel. Inner diameters are cut large to allow for hot dip galvanized bolts to fit through easily, and to also provide adjustment and alignment. 2" Square is the most popular size, and our .250" thick Stainless Steel provides extra strength and load carrying capability, with outstanding corrosion resistance. Made in the USA.

Visit Store Now !!

Detail Products

Detail Reviews

Stainless Steel 18-8 Internal Tooth Lock Washer, ANSI, #4, 0.123" ID, 0.270" OD, 0.015" Thick (Pack of 100)

Stainless Steel 18-8 Internal Tooth Lock Washer, ANSI, #4, 0.123" ID, 0.270" OD, 0.015" Thick (Pack of 100) Reviews

Other Picture

Stainless Steel 18-8 Internal Tooth Lock Washer, ANSI, #4, 0.123" ID, 0.270" OD, 0.015" Thick (Pack of 100) Feature

• Lock Washers ensure a tight assembly
• Stainless Steel is suitable where formability and cost are important considerations
• Size Name corresponds to matching screw or bolt size

Stainless Steel 18-8 Internal Tooth Lock Washers have small teeth along the inside diameter that bite deep into the screw head as well as the work surface, to provide continuing resistance to removal rotation. They are designed to actually lock tighter as vibration increases. These washers meet standards for Internal Tooth Lock Washers Type A under ANSI/ASME B 18.21.1 1994.

Visit Store Now !!

Detail Products

• Stainless Steel Hex Nut, #4-40 (Pack of 100)
• Stainless Steel Machine Screw, Pan Head, Phillips Drive, #1-72, 5/16" Length (Pack of 100)
• Zinc Plated Steel Split Lock Washer, #6, 0.148" ID, 0.25" OD, 0.031" Thick (Pack of 100)
• Stainless Steel Machine Screw, Pan Head, Phillips Drive, MIL-SPEC, #8-32, 1-3/8" Length (Pack of 10)
• Stainless Steel Machine Screw, Flat Head, Slotted Drive, #10-32, 1/4" Length (Pack of 100)

Detail Reviews

Component Flat Washer, 18-8 Stainless Steel, Round Shape, USA Made, 1/4" Bolt Size, 0.281" ID, 0.500" OD, 0.078" Thick (Pack of 5)

Component Flat Washer, 18-8 Stainless Steel, Round Shape, USA Made, 1/4" Bolt Size, 0.281" ID, 0.500" OD, 0.078" Thick (Pack of 5) Reviews

Other Picture

Component Flat Washer, 18-8 Stainless Steel, Round Shape, USA Made, 1/4" Bolt Size, 0.281" ID, 0.500" OD, 0.078" Thick (Pack of 5) Feature

• Component Flat Washers are manufactured with thicker materials for extra strength and load distribution properties
• The most popular sizes of extra strength steel washers in a corrosion resistant stainless steel
• 18-8 Stainless Steel is a good looking (bright and shiny) material with good surface finish and corrosion resistance
• Used anywhere a thick, strong, and corrosion resistant good looking washer is required
• Made In USA for excellent quality conformance

Component Flat Washers are named for their original popularity as a component of a jig or fixture, where a thicker washer was needed for the extra strength and load distribution properties that accompany the extra thickness. Our Component Washers are available from #4 screw size all the way thru 1-1/2" Bolt sizes. All Component Washers are thicker than any standard washer in general use. We provide two lines from stock - Thick and Extra Thick. Smaller diameters have a 5/64" thickness, going all the way up to 3/8" thickness, with the 1/8" thick line being the most popular. These washers are either stamped on power presses or turned on our lathes depending on the quantities we manufacture, and the wall thickness of the washer, which is the relationship between the thickness and the Inner Diameter dimension. All of these are suitable for use anywhere extra strength is needed. 18-8 Stainless Steel material offers excellent corrosion resistance, are harder than Brass, exhibit a slight magnetism, and are an attractive silver color.

Made in the USA. These flat washers are produced in the USA for excellent quality conformance. One of the significant differences between less expensive imported products and ours are the way we stamp. Many cheap imports are produced on gang dies that produce 10 or more washers per stroke of the press. Using such a large die means that the individual washer sets are not adjustable - when the punch wears, the dimensions change and there is no way to fix this as the press produces washers, leading to a large variation in the finished part.

Materials available in many other countries are not as consistent as the domestic steels we use, which gives the imports a cheaper cost, but can lead to failures and inconsistencies when the products are used. The Defense Federal Acquisition Regulation Supplement (DFARS) was created to address this problem. Our materials are DFARS compliant although we do not supply the certification except on special order.

Visit Store Now !!

Detail Products

• Stainless Steel 316 Hex Bolt, 1/4"-20, 2" Length (Pack of 10)

Detail Reviews